Updating portage cache Sexychatsite

Refer to this article by Aaron Toponce for details on how to set up an ARC.

Without configuration, ZFS will use up to 50% of your memory (RAM) for the ARC. There are different ways to achieve this on both a temporary and persistent basis. Aaron Toponce's Zpool/ZFS Administration Guides - https://pthree.org/2012/12/04/zfs-administration-part-i-vdevs ZFS on Linux - - Gentoo Wiki - https://wiki.gentoo.org/wiki/ZFS You will need to chroot into your Funtoo on ZFS root installation if you forgot to set the root password.

Coral Cache, also known as Coral Content Distribution Network or Coral, is a free peer-to-peer type web cache based on thepeer-to-peer content distribution network designed and operated by Michael Freedman.

Coral uses the bandwidth of a world-wide network of web proxies and nameservers to mirror web content, often to avoid the Slashdot Effect or to reduce the load on websites servers in general.

Please note that the options 'ashift' and 'cachefile' are preceded with a lowercase '-o', while 'normalization' and 'atime' are preceded with an uppercase '-O'.

Mounting your root partition (/) will fail since this location is not empty; / is allocated to the live CD/USB distribution! Follow the earlier set of instructions to chroot into your Funtoo Installation on ZFS root.

Repeat the earlier instructions to load the the live CD/USB, including the installation of ZFS kernel modules.

When the ZFS kernel modules are loaded, your existing ZFS Storage Pool (rpool) will be imported automatically.

Google Cache is normally referred as the copies of the web pages cached by Google.

Google crawls the web and takes snapshots of each page as a backup just in case the current page is not available. These Google cached pages can be extremely useful if a site is temporary down, you can always access these page by visiting Google’s cached version. The actual time of the updates depends on the frequency the website updates itself.

Search for updating portage cache:

updating portage cache-33updating portage cache-13updating portage cache-14updating portage cache-59

[ 5.533491] usb 6-2: new Super Speed USB device number 4 using xhci_hcd [ 0.022995] usb 6-2: New USB device found, id Vendor=1b1c, id Product=1a0c [ 0.000006] usb 6-2: New USB device strings: Mfr=1, Product=2, Serial Number=3 [ 0.000003] usb 6-2: Product: Voyager Mini 3.0 [ 0.000003] usb 6-2: Manufacturer: Corsair [ 0.000002] usb 6-2: Serial Number: 0123456789ABCDEF [ 0.001095] usb-storage 6-2:1.0: USB Mass Storage device detected [ 0.000080] scsi host15: usb-storage 6-2:1.0 [ 1.000772] scsi 15:0:0:0: Direct-Access Corsair Voyager Mini 3.0 PMAP PQ: 0 ANSI: 6 [ 0.000615] sd 15:0:0:0: Attached scsi generic sg6 type 0 [ 0.000110] sd 15:0:0:0: [sdg] 60566016 512-byte logical blocks: (31.0 GB/28.9 Gi B) [ 0.000209] sd 15:0:0:0: [sdg] Write Protect is off [ 0.000004] sd 15:0:0:0: [sdg] Mode Sense: 2b 00 00 08 [ 0.000227] sd 15:0:0:0: [sdg] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 0.359532] sd 15:0:0:0: [sdg] Attached SCSI removable disk Once this has completed, remove and use this USB to boot the target system that will receive Funtoo Linux.

Leave a Reply

Your email address will not be published. Required fields are marked *

One thought on “updating portage cache”